High Quality for Long-time high power 150w led gas station canopy lights Factory in Las Vegas
High Quality for Long-time high power 150w led gas station canopy lights Factory in Las Vegas Detail:
Long-time high power 150w led gas station canopy lights
|Product Name||waterproof 150w led flood light|
|Color temp||White/Warm White|
|Lamp Luminous Efficiency(lm/w)||80LM/W|
|Color indexc(CRI)||Ra ≥80|
wall, advertising board, store,
1. Optical light distribution, no glare, no light pollution, high lighting effect and high uniformity.
2. High power factor, energy conservation and environment protection.
3. Surface treatment: coating treatment, high weather-ability, and rich colors.
4. Integrated heat dispersion of the housing; artistic and novel appearance design.
Matters Needing Attention
1. The light’s waterproof grade is IP65, able to withstand rains, but it can’t work under water.
2. Cut off power supply before and in installation process. If the product is damaged due to mal-operation, it shall not be guaranteed. Please have it mounted by a professional.
3. The light’s operating ambient temperature is between -25℃ and 45℃. The temperature of operational site shall not exceed 45℃, to ensure the light’s service life.
4. Since the light power is high, when power line is arranged, it’s necessary to select a proper power line according to actual power, and supply power in single phase.
5. Please don’t dismount the light without authorization. Please contact professional maintenance personnel or the manufacturer if the light isn’t lit or is faulty otherwise.
Warranty waterproof 150w led flood light ce rohs Applications for shopping center,exhibition hall,parking lot, stadium,gymnasia,billboard,park,statue,government lighting decoration project, landmark or building, public square and passage,building connecting passage,and other indoor or outdoor light applications.
Product detail pictures:
Related Product Guide:
High Quality for Long-time high power 150w led gas station canopy lights Factory in Las Vegas , The product will supply to all over the world, such as: , , ,
Check out our blog for clickable links to the items below!
Things you will need:
- Stock tank (size of your choosing- ours is 8 ft.)
- Above Ground Pool Pump
- Weatherproof Silicone Sealant
- Hole Saw with Arbor
- Plunger Valves
- Pool Outlet
- 1-3 Rubber Washers (or Gaskets)
- 1 Strainer Nut
Other things you will need for maintenance:
- Chlorine Tablets
- Floating Pool Dispenser
- Water Testing Kit
Step 1- Find a nice level area to lay the stock tank on. If the area where you have chosen isn’t level, use sand or rocks to build up whatever side needs it. It is very important that your stock tank be level so there aren’t any unexpected leaks.
Step 2- Cut holes in your stock tank. I’m not going to lie- this is a pain in the butt. We bought a hole saw with an arbor and it took two people to get through the metal. You will need two holes, one at the top and one at the bottom. In an above ground pool, these aren’t usually right on top of each other, but ours are. We haven’t ever seen this as a problem.
Step 3- Start assembling the parts. In the pool pump package there is a packet with instructions, warnings and troubleshooting. This packet proved to be vital in the setup of the pool. I did end up getting 2 gaskets for the bottom section (the drain section), one for the inside of the pool and one for the outside. It only says you need one for the inside, but this was causing a drip for us. I also put thread seal tape around the connections that were closest to the pool. There are a lot of connections, and each one has a gasket, so you could probably get away without the tape. I didn’t put it on all the connections, the only ones that really seemed to matter were the ones that are connecting the hoses to the pool.
Step 4- Apply silicone waterproof sealant around all crevices involving the input and output parts. I did this on the inside of the pool and the outside. And I applied it VERY HEAVILY and did two layers, allowing one to dry before the second was applied. Sealing these crevices is one of the most important parts. This is what is going to keep the water in the pool. Well all of these steps are leading up to keeping water in the pool, but if there is any chance that it’s going to be getting out, this is what will save you.
Step 5- Test for leaks. Before I added water to the pool, I took a water bottle and poured a good amount of water on the input and output parts. You could also just use a water hose. I would make sure the hose wasn’t on full blast. You don’t want to accidentally penetrate the sealant.
Step 6- Once you are sure there aren’t any leaks, fill the pool just above the bottom hole/output. Check again to see if any leaks have started. If there aren’t any, fill the rest of the pool up!
Step 7- Turn the pump on. Make sure both plunger valves are open/unlocked. When you first do this water may not come out of the output, but there is a solution! Twist off the knob on top of the filter pump to let some air out. Some water may escape too and that’s okay, just be ready to screw it back on as soon as the water starts coming out.
By from -
By from -